View MC10138_129020.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

MOTOROLA
SEMICONDUCTOR TECHNICAL DATA
Bi-Quinary Counter
The MC10138 is a four bit counter capable of divide by two, five, or ten functions. It is composed of four set-reset master-slave flip-flops. Clock inputs trigger on the positive going edge of the clock pulse. Set or reset input override the clock, allowing asynchronous "set" or "clear." Individual set and common reset inputs are provided, as well as complementary outputs for the first and fourth bits. PD = 370 mW typ/pkg (No Load) ftog = 150 MHz typ tr, tf = 2.5 ns typ (20%-80%) LOGIC DIAGRAM
S0 11 15 Q0 10 S1 13 Q1 6 S2 4 Q2 5 S3 2 Q3
MC10138
L SUFFIX CERAMIC PACKAGE CASE 620-10 P SUFFIX PLASTIC PACKAGE CASE 648-08 FN SUFFIX PLCC CASE 775-02
S D1 12 Clock Q Q' C1 R 9 Reset 14 Q0 C2 7 Q D1 D2 C2
S Q Q' Q R D1 C1 C2
S Q Q' Q R D1 D2 C2
S Q' Q Q R
DIP PIN ASSIGNMENT
VCC1
3
1 2 3 4 5 6 7 8
16 15 14 13 12 11 10 9
VCC2 Q0 Q0 Q1 C1 S0 S1 RESET
Q3
Q3
VCC1 = PIN 1; VCC2 = PIN 16; VEE = PIN 8
Q3 Q2 S3 S2 Q3 L L L L L L L L H H C2 VEE
COUNTER TRUTH TABLES
BI-QUINARY (Clock connected to C2 and Q3 connected to C1) COUNT 0 1 2 3 4 5 6 7 8 9 Q1 L H L H L L H L H L Q2 L L H H L L L H H L Q3 L L L L H L L L L H Q0 L L L L L H H H H H 0 1 2 3 4 5 6 7 8 9 BCD (Clock connected to C1 and Q0 connected to C2) COUNT Q0 L H L H L H L H L H Q1 L L H H L L H H L L Q2 L L L L H H H H L L
Pin assignment is for Dual-in-Line Package. For PLCC pin assignment, see the Pin Conversion Tables on page 6-11 of the Motorola MECL Data Book (DL122/D).
COUNTER STATE DIAGRAM -- POSITIVE LOGIC
CLOCK CONNECTED TO C2
0 0
Q0 CONNECTED TO C2
1 2 3 4
4
7
1
14
10
11
5 6 3 2 9
15
12
13
8
7
6
5
3/93
(c) Motorola, Inc. 1996
3-41
REV 5
MC10138
ELECTRICAL CHARACTERISTICS
Test Limits Pin Pi Under Test 8 12 5,6,10,11 7 9 All 3,14 (3.) 2,4,13,15 (2.) 3,14 (2.) 2,4,13,15 (3.) 2,4,13,15 (2.) 3,14 (3.) 13,15 (2.) 2,4,13,15 (3.) 3,14 (2.) 13,15 (3.) 0.5 -1.060 -1.060 -1.890 -1.890 -1.080 -1.080 -1.080 -1.655 -1.655 -1.655 -0.890 -0.890 -1.675 -1.675 -30C Min Max 97 350 390 460 650 0.5 -0.960 -0.960 -1.850 -1.850 -0.980 -0.980 -0.980 -1.630 -1.630 -1.630 -0.810 -0.810 -1.650 -1.650 Min +25C Typ 70 Max 88 220 245 290 410 0.3 -0.890 -0.890 -1.825 -1.825 -0.910 -0.910 -0.910 -1.595 -1.595 -1.595 -0.700 -0.700 -1.615 -1.615 Min +85C Max 97 220 245 290 Unit mAdc Adc
Characteristic Power Supply Drain Current Input Current
Symbol IE IinH
IinL Output Voltage Output Voltage Threshold Voltage Logic 1 Logic 0 Logic 1 VOH VOL VOHA
Adc Vdc Vdc Vdc
Threshold Voltage
Logic 0
VOLA
Vdc
Switching Times Propagation Delay
(50 Load) Clock Delays t12+15+ t12+14+ t7+13+ t7+4+ t7+2+ t7+3+ t12+15- t12+14- t7+13- t7+4- t7+2- t7+3- 15 14 13 4 2 3 15 14 13 4 2 3 15 14 14 15 14 15 14 15 2 15 1.4 1.4 1.4 1.4 1.4 1.4 1.4 1.4 1.4 1.4 1.4 1.4 1.4 1.4 1.4 1.4 1.1 1.1 1.1 1.1 125 125 5.0 5.0 5.2 5.2 5.2 5.2 5.0 5.0 5.2 5.2 5.2 5.2 5.2 5.2 5.2 5.2 4.7 4.7 4.7 4.7 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.1 1.1 1.1 1.1 125 125 2.5 2.5 2.5 2.5 150 150 3.5 3.5 3.5 3.5 3.5 3.5 3.5 3.5 3.5 3.5 3.5 3.5 4.8 4.8 5.0 5.0 5.0 5.0 4.8 4.8 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 4.5 4.5 4.5 4.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.1 1.1 1.1 1.1 125 125 5.3 5.3 5.5 5.5 5.5 5.5 5.3 5.3 5.5 5.5 5.5 5.5 5.5 5.5 5.5 5.5 5.0 5.0 5.0 5.0
ns
Set Delay Reset Delay Rise Time Fall Time (20 to 80%) (20 to 80%)
t11+15+ t11+14- t9+14+ t9+15- t14+ t15+ t14- t15- fcount
Counting Frequency
MHz
1. Individually test each input; apply VILmin to pin under test. VIHmax 2. Set all four flip-flops by applying pulse 3. Reset all four flip-flops by applying pulse VILmin VIHmax VILmin
to pins 5, 6, 10, and 11 prior to applying test voltage indicated. to pin 9 prior to applying test voltage indicated.
MOTOROLA
3-42
MECL Data DL122 -- Rev 6
MC10138
ELECTRICAL CHARACTERISTICS (continued)
NOTE: Each MECL 10,000 series circuit has been designed to meet the dc specifications shown in the test table, after thermal equilibrium has been established. The circuit is in a test socket or mounted on a printed circuit board and transverse air flow greater than 500 linear fpm is maintained. O Outputs are terminated through a 50-ohm resistor to -2.0 volts. Test p procedures are shown for only one gate The other gates are gate. tested in the same manner.
TEST VOLTAGE VALUES (Volts) @ Test Temperature -30C +25C +85C Pin Under Test 8 12 5,6,10,11 7 9 All 3,14 (3.) 2,4,13,15 (2.) 3,14 (2.) 2,4,13,15 (3.) 2,4,13,15 (2.) 3,14 (3.) 13,15 (2.) 2,4,13,15 (3.) 3,14 (2.) 13,15 (3.) Pulse In t12+15+ t12+14+ t7+13+ t7+4+ t7+2+ t7+3+ t12+15- t12+14- t7+13- t7+4- t7+2- t7+3- 15 14 13 4 2 3 15 14 13 4 2 3 15 14 14 15 14 15 14 15 2 15 12 12 7 7 7 7 12 12 7 7 7 7 11 11 9 9 11 11 9 9 7 12 9 5,6,10,11 5,6,10,11 9 5,6,10,11 9 7,12 5,6,10,11 9 7,12 Pulse Out 15 14 13 4 2 3 15 14 13 4 2 3 15 14 14 15 14 15 14 15 2 15 VIHmax -0.890 -0.810 -0.700 VILmin -1.890 -1.850 -1.825 VIHAmin -1.205 -1.105 -1.035 VILAmax -1.500 -1.475 -1.440 VEE -5.2 -5.2 -5.2
TEST VOLTAGE APPLIED TO PINS LISTED BELOW VIHmax 9 12 5,6,10,11 7 9 Note 1. VILmin VIHAmin VILAmax VEE 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 -3.2 V 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 (VCC) Gnd 1, 16 1, 16 1, 16 1, 16 1, 16 1, 16 1, 16 1, 16 1, 16 1, 16 1, 16 1, 16 1, 16 1, 16 1, 16 1, 16 +2.0 V 1, 16 1, 16 1, 16 1, 16 1, 16 1, 16 1, 16 1, 16 1, 16 1, 16 1, 16 1, 16 1, 16 1, 16 1, 16 1, 16 1, 16 1, 16 1, 16 1, 16 1, 16 1, 16
Characteristic Power Supply Drain Current Input Current
Symbol IE IinH
IinL Output Voltage Output Voltage Threshold Voltage Logic 1 Logic 0 Logic 1 VOH VOL VOHA
Threshold Voltage
Logic 0
VOLA
Switching Times Propagation Delay
(50 Load) Clock Delays
Set Delay Reset Delay Rise Time Fall Time Counting Frequency (20 to 80%) (20 to 80%)
t11+15+ t11+14- t9+14+ t9+15- t14+ t15+ t14- t15- fcount
1. Individually test each input; apply VILmin to pin under test. VIHmax 2. Set all four flip-flops by applying pulse 3. Reset all four flip-flops by applying pulse VILmin VIHmax VILmin
to pins 5, 6, 10, and 11 prior to applying test voltage indicated. to pin 9 prior to applying test voltage indicated.
MECL Data DL122 -- Rev 6
3-43
MOTOROLA
MC10138
OUTLINE DIMENSIONS
FN SUFFIX PLASTIC PLCC PACKAGE CASE 775-02 ISSUE C
B -N- Y BRK D -L- -M- W D Z
0.007 (0.180) M T L-M U
S
N
S S
0.007 (0.180) M T L-M
N
S
20
1
X V VIEW D-D
G1
0.010 (0.250)
S
T L-M
S
N
S
A Z R
0.007 (0.180) M T L-M 0.007 (0.180) M T L-M
S
N N
S
S
S
H
0.007 (0.180) M T L-M
S
N
S
C
E 0.004 (0.100) G G1 0.010 (0.250) S T L-M J -T-
SEATING PLANE
K1 K F VIEW S 0.007 (0.180)
M
VIEW S
S
T L-M
S
N
S
N
S
NOTES: 1. DATUMS -L-, -M-, AND -N- DETERMINED WHERE TOP OF LEAD SHOULDER EXITS PLASTIC BODY AT MOLD PARTING LINE. 2. DIMENSION G1, TRUE POSITION TO BE MEASURED AT DATUM -T-, SEATING PLANE. 3. DIMENSIONS R AND U DO NOT INCLUDE MOLD FLASH. ALLOWABLE MOLD FLASH IS 0.010 (0.250) PER SIDE. 4. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 5. CONTROLLING DIMENSION: INCH. 6. THE PACKAGE TOP MAY BE SMALLER THAN THE PACKAGE BOTTOM BY UP TO 0.012 (0.300). DIMENSIONS R AND U ARE DETERMINED AT THE OUTERMOST EXTREMES OF THE PLASTIC BODY EXCLUSIVE OF MOLD FLASH, TIE BAR BURRS, GATE BURRS AND INTERLEAD FLASH, BUT INCLUDING ANY MISMATCH BETWEEN THE TOP AND BOTTOM OF THE PLASTIC BODY. 7. DIMENSION H DOES NOT INCLUDE DAMBAR PROTRUSION OR INTRUSION. THE DAMBAR PROTRUSION(S) SHALL NOT CAUSE THE H DIMENSION TO BE GREATER THAN 0.037 (0.940). THE DAMBAR INTRUSION(S) SHALL NOT CAUSE THE H DIMENSION TO BE SMALLER THAN 0.025 (0.635).
DIM A B C E F G H J K R U V W X Y Z G1 K1
INCHES MIN MAX 0.385 0.395 0.385 0.395 0.165 0.180 0.090 0.110 0.013 0.019 0.050 BSC 0.026 0.032 0.020 --- 0.025 --- 0.350 0.356 0.350 0.356 0.042 0.048 0.042 0.048 0.042 0.056 --- 0.020 2_ 10 _ 0.310 0.330 0.040 ---
MILLIMETERS MIN MAX 9.78 10.03 9.78 10.03 4.20 4.57 2.29 2.79 0.33 0.48 1.27 BSC 0.66 0.81 0.51 --- 0.64 --- 8.89 9.04 8.89 9.04 1.07 1.21 1.07 1.21 1.07 1.42 --- 0.50 2_ 10 _ 7.88 8.38 1.02 ---
MOTOROLA
3-44
MECL Data DL122 -- Rev 6
MC10138
OUTLINE DIMENSIONS
L SUFFIX CERAMIC DIP PACKAGE CASE 620-10 ISSUE V
9
-A-
16
-B-
1 8
C
L
NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION L TO CENTER OF LEAD WHEN FORMED PARALLEL. 4. DIMENSION F MAY NARROW TO 0.76 (0.030) WHERE THE LEAD ENTERS THE CERAMIC BODY. DIM A B C D E F G H K L M N INCHES MIN MAX 0.750 0.785 0.240 0.295 --- 0.200 0.015 0.020 0.050 BSC 0.055 0.065 0.100 BSC 0.008 0.015 0.125 0.170 0.300 BSC 0_ 15 _ 0.020 0.040 MILLIMETERS MIN MAX 19.05 19.93 6.10 7.49 --- 5.08 0.39 0.50 1.27 BSC 1.40 1.65 2.54 BSC 0.21 0.38 3.18 4.31 7.62 BSC 0_ 15 _ 0.51 1.01
-T-
SEATING PLANE
N E F D G
16 PL
K M J
16 PL
0.25 (0.010)
M
M
TB
S
0.25 (0.010)
TA
S
-A-
16 9
P SUFFIX PLASTIC DIP PACKAGE CASE 648-08 ISSUE R
B
1 8
NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION L TO CENTER OF LEADS WHEN FORMED PARALLEL. 4. DIMENSION B DOES NOT INCLUDE MOLD FLASH. 5. ROUNDED CORNERS OPTIONAL. DIM A B C D F G H J K L M S INCHES MIN MAX 0.740 0.770 0.250 0.270 0.145 0.175 0.015 0.021 0.040 0.70 0.100 BSC 0.050 BSC 0.008 0.015 0.110 0.130 0.295 0.305 0_ 10 _ 0.020 0.040 MILLIMETERS MIN MAX 18.80 19.55 6.35 6.85 3.69 4.44 0.39 0.53 1.02 1.77 2.54 BSC 1.27 BSC 0.21 0.38 2.80 3.30 7.50 7.74 0_ 10 _ 0.51 1.01
F S
C
L
-T- H G D
16 PL
SEATING PLANE
K
J TA
M
M
0.25 (0.010)
M
Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. "Typical" parameters which may be provided in Motorola data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. How to reach us: USA/EUROPE/Locations Not Listed: Motorola Literature Distribution; P.O. Box 5405, Denver, Colorado 80217. 303-675-2140 or 1-800-441-2447 MfaxTM: RMFAX0@email.sps.mot.com - TOUCHTONE 602-244-6609 INTERNET: http://Design-NET.com
JAPAN: Nippon Motorola Ltd.; Tatsumi-SPD-JLDC, 6F Seibu-Butsuryu-Center, 3-14-2 Tatsumi Koto-Ku, Tokyo 135, Japan. 81-3-3521-8315 ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park, 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852-26629298
MECL Data DL122 -- Rev 6 3-45
*MC10138/D*
MC10138/D MOTOROLA

▲Up To Search▲

Price & Availability of MC10138

	To Download MC10138 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .